About wallpaper seams, repair wall stickers
Specific steps and precautions for several wall postings such as wallpaper seams and repairs:
First, the seam treatment
First, use a knife to pick up the seams, use a special small brush, carefully from top to bottom, apply special glue (the ratio of wallpaper powder to white glue is 1:1), when brushing the glue, use 1cm for l segment, brush two Under, try not to let the glue overflow the surface of the wallpaper. If it overflows, immediately wipe it with a white towel or sponge.
Next, gently flatten the seam at a 30 degree angle to the wall at 1 cm from the tip of the squeegee.
Again, if there is overlap in the seams, first gently move the wallpaper overlaid on the top, double the two wallpapers, and then smooth the seams with the scraper.
Finally, use the pressure roller to flatten the joint from top to bottom. Pay attention to the flattening of 1cm for each section. Press each section up and down three times. The force should not be large and should be light and uniform.
Second, the wallpaper is posted on a special part of the wall
â—Post the wallpaper at the corner
Step 1: Use a scraper to carefully attach the wallpaper and cross the corner of the wall, but do not stick to the other wall.
Step 2: Use your hand to crease the crease from the top of the convex wall corner. From the ceiling to the floor, draw a vertical line from the ceiling to the floor.
Step 3: Use a utility knife to cut the wallpaper along the above vertical line, and guide it with a ruler.
Step 4: Carefully pull the remaining wallpaper and put it on the workbench for later use.
Step 5: Use the seaming roller to flatten the overhanging part of the wallpaper, and add glue to the glue on the covered wallpaper.
Step 6: Cover the wallpaper and smash it up, spell the pattern, scrape the wallpaper with a scraper, and flatten it with a pressure roller.
â— posted at the corner of the wallpaper
1) Treatment of the house without the negative angle of settlement
The first step: measuring from the center of the last wallpaper to the concave corner, plus 2.5cm, cut a piece of wallpaper according to this width.
Step 2: Attach the above-mentioned piece of wallpaper, align it with the last attached wallpaper and flatten it on the corner of the concave wall.
The third step: use the scraper to scrape the outer part to stick to the wall, and dry the glue on the scraper.
Step 4: Measure the width of the segment from the concave corner and add 5mm to mark the wall.
Step 5: Place the level on the pencil mark to check if it is really vertical and apply glue to the covered wallpaper.
Step 6: Align the outside of the covered wallpaper with the vertical line. The vertical line shall prevail and affix the rest of the wallpaper.
2) Treatment method for the negative angle of settlement of the house
The first step - the third step: the same as above.
Step 4: Paste another wallpaper with the previous wallpaper, align the wallpaper and turn to the other wall.
Step 5: Flatten the negative corner of the back of the scraper at the female corner.
*Note: First slowly close the wallpaper to the negative angle with your hand, and then slowly flatten the negative angle on the back of the scraper. Do not use force to avoid hurting the wallpaper.
Step 6: Make a crease along the scraper at a distance of 2mm from the negative angle. Use a ruler to fit the utility knife and cut it from top to bottom.
Step 7: Remove the excess wallpaper and wipe off the excess glue with a white towel or sponge.
Bathroom basket,bathroom rack,bathroom holder,hanging basket,stainless steel basket,etc. Let your bathroom become more simple and upscale!Applicable to families, hotels, home stay and other places to use.
304 stainless steel never rust, will easy to clear, it's also very durable!
we are 15 year factory, we had big engineer team, and strong production line, can give you good serve and quanlity. Welcome to cooperation!
bathroom holder,hanging basket,stainless steel basket,bathroom wall basket,bathroom hanging basket
Shenzhen Lanejoy Technology Co.,LTD , https://www.injectionnut.com