Housing product use and device orientation
| Home>Bearing knowledge> Bearing housing product use and device orientation |
Housing product use and device orientation
Source: China Bearing Network Time: 2014-02-07
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
This type of product is equipped with 2 series bearings, 3 series bearings; the most typical and most commonly used type of spheroidal spherical ball bearings; suitable for all transmissions and shafts parallel to the machine surface. Strength and rigidity.
2, square flange seat: F200 series (F203-F220), F300 series (F305-F328)
This type of product is equipped with 2 series bearings and 3 series bearings; it is usually installed on the side wall of the machine; the layout is simple; the device is convenient; it is suitable for heavy load occasions. It is the most widely used type of flange type bearing housing.
3, diamond flange seat: FL200 series (F203-F218), FL300 series (FL305-FL315)
This type of product is equipped with 2 series bearings and 3 series bearings; the layout is light and convenient; it is suitable for the transmission part with small area. The spacing between the two bolt holes is the same as the spacing between the diagonal holes of the same type of square seat. Can replace the square seat.
4, narrow vertical seat: PA200 series (PA203-PA213), PA300 series (PA305-PA313)
This type of product is equipped with 2 series bearings and 3 series bearings; there are two device screw holes at the bottom; the width is greatly tightened; it is suitable for the limited area of ​​the device.
5, high middle vertical seat: PH200 series (PH203-PH213)
This type of product is equipped with 2 series bearings; usage and use are common with UCP200; difference axis intermediate height ratio is usually vertical seat height.
6. Suspended seat: HA200 series (HA203-HA213)
This type of product is equipped with 2 series bearings; the bearing housing is equipped with a conditioning screw hole at one end; the bearing housing can be coupled to the screw to adjust the orientation of the device; usually used in applications where the load is small.
7. Adjustable diamond seat: FA200 series (FA203-FA213)
This type of product is equipped with 2 series bearings; a deformation of the diamond seat. One of the bolts is changed to an arc groove positioned in the middle of the other hole. Therefore, the axial position can be adjusted within a certain range.
8, three-hole flange diamond seat: FB200 series (FB203-FB213)
This type of product is equipped with 2 series bearings; a deformation of the diamond seat; the three device bolt holes are concentrated on one side of the seat. It is suitable for the position where the device surface is in a straight condition; it can be used instead of the vertical seat.
9. Boss round flange seat: FC200 series (FC203-FC220)
This type of product is equipped with 2 series bearings; it is a round flanged bearing seat with a circular boss on the bottom; it can be placed in the circular hole of the frame; thus the device has high precision and accurate positioning.
10, boss square bearing housing: FS300 series (FS305-FS328)
This type of product is equipped with 3 series bearings; it is a square flange bearing seat with a circular boss on the bottom; it can be placed in the circular hole of the frame; thus the device has high precision and accurate positioning.
11. Slider seat: T200 series (T203-T220), T300 series (T305-T328), K200 series (K203-K212)
This type of product is equipped with 2 series bearings and 3 series bearings; there are two chutes on the upper and lower sides. It can move back and forth on the frame. Therefore, it is most suitable for the occasion to adjust the spacing between the shafts. The shaft can also be moved during the work. Mostly used on belts; chains and other drive shafts.
12, ring seat: C200 series (C203-C218), C300 series (C305-C328) and other products of this type are equipped with 2 series bearings, 3 series bearings; outer diameter machining of the bearing housing; can be embedded in the frame Inside the hole; can accept a large radial load; used on a relatively heavy rack.
Outer spherical steel stamping seat type:
1. Stamping vertical seat: PP200 series is equipped with 2 series bearings; it is composed of upper and lower shells stamped by steel plate; it is lighter than cast iron vertical seat; small size is small; it is the smallest seat in vertical stand Type. But only for occasions with small load.
2, stamping round seat CY200 series with 2 series bearings; consists of two stamped circular shells that can be exchanged; use high-quality steel plate scouring; its function is similar to its similar cast iron seat; because the stamping seat is light and compact; In the smaller installation space; the load is more difficult to boring and milling.
3, stamping diamond seat CL200 series with 2 series bearings; this stamping seat has an outstanding device space; it is the most spherical shape of the spherical bearing.
Recommend to friends comments close window
| Bearing related knowledge |
| FAG bearing inner ring fixing method commonly used SKF bearing repair type inspection and repair NSK bearing's primary skill rolling bearing ferrule production processing rolling bearing common terms and definitions (1) |
This article links to http://
Please indicate the bearing network http://
Previous:Imported bearing inner packaging depicting the next series: What grades are the rolling bearing dividends?
PRO-CHARGER CO., LTD. (VICTOR HERO HOLDINGS LTD, TIME VALUE LTD.) , https://www.pro-chargerco.com