Car wheel bearing nine installation matters and common sense
Common sense of installation and use of automotive wheel bearings
The largest number of wheel bearings for cars used in the past was the use of single row tapered roller or ball bearings in pairs. With the development of technology, car hub units have been widely used in cars. The range and use of hub bearing units is growing, and has now reached the third generation: the first generation consists of double row angular contact bearings. The second generation has a flange for fixing the bearing on the outer raceway, which can be simply fixed to the axle by a nut. Make the maintenance of the car easier. The third-generation hub bearing unit is matched with the bearing unit and the anti-lock brake system ABS. The hub unit is designed with an inner flange and an outer flange, the inner flange is bolted to the drive shaft, and the outer flange mounts the entire bearing together. Worn or damaged hub bearings or hub units can cause unacceptable and costly failures in your vehicle's travel path and even cause damage to your safety.
Please pay attention to the following items during the use and installation of the hub bearing:
1. In order to ensure maximum safety and reliability, it is recommended that you always check the hub bearing regardless of the length of the car – pay attention to whether the bearing has early warning signs of wear: including any friction noise during rotation or suspension of the combined wheel in the turn When the speed is not normal. For rear-wheel-drive vehicles, it is recommended to lubricate the front hub bearings when the vehicle travels to 38,000 km. When replacing the brake system, check the bearings and replace the oil seal.
2. If you hear the noise from the bearing parts of the hub, first of all, it is important to find the location where the noise occurs. There are many moving parts that may produce noise, or some rotating parts may come into contact with the non-rotating parts. If it is confirmed that the noise is in the bearing, the bearing may be damaged and needs to be replaced.
3. Because the front hub causes the working conditions of the bearings on both sides to be similar, it is recommended to replace them in pairs even if only one bearing is broken.
4, the wheel bearing is more sensitive, in any case need to use the correct method and the right tool. The components of the bearing must not be damaged during storage and installation. Some bearings require a large pressure to press in, so special tools are required. Be sure to refer to the car manufacturer's instructions.
5, when installing the bearing should be in a clean and tidy environment, the fine particles into the bearing will also shorten the service life of the bearing. It is very important to keep the environment clean when replacing bearings. It is not allowed to hit the bearing with a hoe, pay attention to the bearing not to fall to the ground (or similarly improper handling). The condition of the shaft and housing should also be checked before installation. Even minor wear can cause poor fit and cause early failure of the bearing.
6. For the hub bearing unit, do not attempt to disassemble the hub bearing or adjust the seal ring of the hub unit, otherwise the seal ring will be damaged and water or dust will enter. Even the raceways of the seal ring and the inner ring are damaged, resulting in permanent failure of the bearing.
7. There is a magnetic thrust ring in the seal ring bearing the ABS device bearing. The thrust ring cannot be impacted, impacted or collided with other magnetic fields. Remove from the box before installation and keep them away from magnetic fields, such as electric motors or power tools. When installing these bearings, observe the ABS alarm needle on the instrument panel through the road condition test to change the operation of the bearing.
8. For the hub bearing equipped with the ABS magnetic thrust ring, in order to determine which side of the thrust ring is mounted, a light and small thing can be used near the edge of the bearing, and the magnetic force generated by the bearing will attract it. When installing, point the side with the magnetic thrust ring to the inside, facing the sensitive component of the ABS. Note: Improper installation may result in malfunction of the brake system.
9. Many bearings are sealed. These bearings do not need to be greased throughout their life. Other unsealed bearings such as double row tapered roller bearings must be greased during installation. Because the inner cavity of the bearing is different in size, it is difficult to determine how much grease to add. The most important thing is to ensure that there is grease in the bearing. If the grease is too much, when the bearing rotates, the excess grease will seep out. General experience: When installing, the total amount of grease should account for 50% of the bearing clearance.
10. When installing the lock nut, the torque varies greatly depending on the bearing type and the bearing housing. Note the relevant instructions.
Concerned about surprises
Tag: Bearing sleeve Wheel bearing Automobile wheel Bearing installation Lock nut
Previous: Bearing knowledge: Introduction to automobile wheel bearings Next: Steel market encounters "Golden three silver four" can rebound
1. Solar panel : 4.5W 9W 18W 17% efficiency More than 10 years lifespan
2. LED : White LEDs 24pcs 48pcs 60pcs/More
3. Charging Method : Solar power
4, Charging time :7-8hrs
5.Lighting time: 2-3 days once full charged 5 hrs 100% bright there after 25% Dim till dawn
6.Battery : 18650 li-ion battery 3.7V 4400mAh/8800mah/17600mah
7. Material : Aluminum Alloy+ABS IP level : IP65
9. With Light sensor Working Temperature: -25℃ to 65℃
10.Very suitable using in Double side real estate signboard, Garden,Park,Pathway, courtyard, street,roadway, sidewalk, farm & ranch etc ,
Signboard , billboard lighting , and door number plate .
Solar Billboard Light,Aluminum Solar Billboard Light,Double Color Solar Billboard Lamp.solar billboard spot light
Shenzhen You&My Electronic Technology Co., Ltd , https://www.ymledtrade.com